Massive Selection for Stanley Hydraulic Power Unit - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai
Massive Selection for Stanley Hydraulic Power Unit - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai
Massive Selection for Stanley Hydraulic Power Unit - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai Detail:
Main Specifications
Motor: AC 380V 1.1KW
Solenoid valve: 2/2ways solenoid control valve
Pump displacement: 3.2CC/REV
System flow: 4.5lpm
Tank: 12L steel square tank
Mounting type: Vertical
Hydraulic power unit
| Power Voltage | AC110, AC220, AC380, DC12V, DC24V or customized |
| Moter Power | 0.75kw, 1.1kw, 1.5kw, 2.2kw, 3.0kw or customized |
| Pump Displacement | 0.45ml/r, 0.75ml/r, 1.0ml/r, 1.6ml/r, 2.0ml/r, 2.5ml/r, 3.3ml/r, 4.2ml/r,5.8 ml/r or customized |
| Solenoid Valve Voltage | DC12V, DC24V, AC24V, AC110V, AC220V, manual valve |
| Mounting Way | Horizontal, Vertical |
| Mounting position | Valve block, bracket, oil tank, electric motor |
| System Pressure | 10mpa, 16mpa, 20mpa, 25mpa |
| Capacity of tank | 1.7L, 2.8L, 3.6L, 5.0L, 6.0L, 8.0L, 10.0L, 12.0L or customized |
| Circuit | 01-20 |
| Port | 3/8″ (BSPP/NPT) or customized |
| Working | Continute working, short time working |
| Frequency | 50HZ, 60HZ |
Precautions for Use
1. Please read the operation manual carefully and check the product model and parameters for correctness.
2. The hydraulic power unit should be installed correctly and connected correctly. Pay attention to whether the voltage of motor and solenoid valve is consistent with the power supply (see electrical schematic diagram), and whether the rotation direction of motor is correct (clockwise from the end of the shaft).
3. Regular
The power unit motor is gap type
4. The work week
The continuous working time of one start is 3 minutes and the rest is 7 minutes. It can not run continuously.
5. The working pressure of the hydraulic power unit has been adjusted when it leaves the factory. In order to maintain a good use state, please do not adjust it casually.
6. The hydraulic power unit should use anti-wear hydraulic oil with a kinematic viscosity of 27 43mm/s(50°C). Ya-n46 is recommended when the oil temperature is lower than 50°C, and YA-N68 is recommended when the oil temperature is higher than 50°C
10~ 25μm filter filter, conventional adding amount is 85~90% of the effective volume of the tank, conventional oil temperature should be within the range of -10~80°C, especially cold areas, low temperature hydraulic oil should be used.
Product detail pictures:
Related Product Guide:
With our excellent administration, potent technical capability and strict top quality control technique, we go on to provide our consumers with trusted quality, reasonable price ranges and fantastic providers. We intention at becoming one among your most trusted partners and earning your fulfillment for Massive Selection for Stanley Hydraulic Power Unit - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai , The product will supply to all over the world, such as: Sheffield, Macedonia, Somalia, We hope we can establish long-term cooperation with all of the customers, and hope we can improve competitiveness and achieve the win-win situation together with the customers. We sincerely welcome the customers from all over the world to contact us for anything you need!Welcome all customers both at home and abroad to visit our factory. We hope to have win-win business relationships with you, and create a better tomorrow.
By Ingrid from Liberia - 2018.06.21 17:11
The customer service staff's attitude is very sincere and the reply is timely and very detailed, this is very helpful for our deal,thank you.
By Nainesh Mehta from Kyrgyzstan - 2018.06.18 17:25
