China Chinese Professional High Pressure Hydraulic Cylinder - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai factory and manufacturers

Chinese Professional High Pressure Hydraulic Cylinder - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai

Short Description:

Product Detail

Product Tags

Feedback (2)

We'll make every effort and hard work to be superb and excellent, and speed up our steps for standing inside the rank of intercontinental top-grade and high-tech enterprises for Ac Power Pack, Hydraulic Power Pack 24v, 12 Volt Electric Lift Cylinder, We are very proud of the good reputation from our customers for our products' reliable quality.

Chinese Professional High Pressure Hydraulic Cylinder - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai Detail:

Main Specifications

Motor: AC 380V 1.1KW
Solenoid valve: 2/2ways solenoid control valve
Pump displacement: 3.2CC/REV
System flow: 4.5lpm
Tank: 12L steel square tank
Mounting type: Vertical
Hydraulic power unit

Power Voltage	AC110, AC220, AC380, DC12V, DC24V or customized
Moter Power	0.75kw, 1.1kw, 1.5kw, 2.2kw, 3.0kw or customized
Pump Displacement	0.45ml/r, 0.75ml/r, 1.0ml/r, 1.6ml/r, 2.0ml/r, 2.5ml/r, 3.3ml/r, 4.2ml/r,5.8 ml/r or customized
Solenoid Valve Voltage	DC12V, DC24V, AC24V, AC110V, AC220V, manual valve
Mounting Way	Horizontal, Vertical
Mounting position	Valve block, bracket, oil tank, electric motor
System Pressure	10mpa, 16mpa, 20mpa, 25mpa
Capacity of tank	1.7L, 2.8L, 3.6L, 5.0L, 6.0L, 8.0L, 10.0L, 12.0L or customized
Circuit	01-20
Port	3/8″ (BSPP/NPT) or customized
Working	Continute working, short time working
Frequency	50HZ, 60HZ

Precautions for Use

1. Please read the operation manual carefully and check the product model and parameters for correctness.
2. The hydraulic power unit should be installed correctly and connected correctly. Pay attention to whether the voltage of motor and solenoid valve is consistent with the power supply (see electrical schematic diagram), and whether the rotation direction of motor is correct (clockwise from the end of the shaft).
3. Regular
The power unit motor is gap type
4. The work week
The continuous working time of one start is 3 minutes and the rest is 7 minutes. It can not run continuously.
5. The working pressure of the hydraulic power unit has been adjusted when it leaves the factory. In order to maintain a good use state, please do not adjust it casually.
6. The hydraulic power unit should use anti-wear hydraulic oil with a kinematic viscosity of 27 43mm/s(50°C). Ya-n46 is recommended when the oil temperature is lower than 50°C, and YA-N68 is recommended when the oil temperature is higher than 50°C
10~ 25μm filter filter, conventional adding amount is 85~90% of the effective volume of the tank, conventional oil temperature should be within the range of -10~80°C, especially cold areas, low temperature hydraulic oil should be used.

AC-380V-1.5KW-Single-Acting-Hydraulic-Power-Packs07

Product detail pictures:

Related Product Guide:

We also offer product sourcing and flight consolidation services. We have our own factory and sourcing office. We can provide you with almost every type of product related to our product range for Chinese Professional High Pressure Hydraulic Cylinder - AC 380V 1.5KW Single Acting Hydraulic Power Packs – Oumai , The product will supply to all over the world, such as: Japan, Brunei, belarus, In order to make more people know our products and to enlarge our market, we have devoted a lot of attention to technical innovations and improvement, as well as replacement of equipment. Last but not the least, we also pay more attention to training our managerial personnel, technicians and workers in planned way.

12 Volt Electric Hydraulic Cylinder